Zendrum Forums

Please login or register.

Login with username, password and session length
Advanced search  
Pages: 1 ... 5 6 [7] 8 9 10
 on: June 14, 2015, 02:37:39 PM 
Started by Ronnie Balz - Last post by Ronnie Balz
Thanks for the quick reply.  I'm maybe not being clear or I'm misunderstanding your reply.  I'm not talking about somehow turning the midi out into a midi in, I'm talking about doing some sort of midi to usb conversion and sending midi from the zendrum into the module usb port.  If one of these modules is plugged into a computer, it can receive midi from a sequencing program like Logic or Digital performer so it seems possible.

 on: June 14, 2015, 12:55:55 PM 
Started by Ronnie Balz - Last post by DrumWagon
The manuals would indicate a 'no'.  There is no mention of MIDI IN or playback of recordings made via MIDI OUT.  Perhaps more telling though is there is no MIDI implementation chart.

 on: June 14, 2015, 12:16:49 AM 
Started by Ronnie Balz - Last post by Ronnie Balz
Is there a way to make a zendrum work with the newer modules (Roland TD-25, TD-15, etc) that don't have midi in?  I know Alternate Mode sells midi to usb cables to go directly into your computer.  Could a cable like that go directly into the module to receive midi?

 on: June 14, 2015, 12:14:07 AM 
Started by wb_drumz - Last post by Ronnie Balz
Was wondering the same thing myself.  I asked 2Box Support.  The reply:  "if you can set up the Hihat to MIDI send:
DrumIt Five MIDI note for HIHAT Edge, Bow and the Pedal  + velocity data for these 3 zone ( 1-127)  and finally controller data for open to close, than it should work."

I, unfortunately am not much of a techie (and don't want to be) so I don't really know what that means.  I suspect I could figure it out but I'm not $1200 confident I can, so...

 on: March 31, 2015, 02:51:42 PM 
Started by wb_drumz - Last post by wb_drumz
Hi folks: Is anyone out there using a 2 Box system? I am interested in whether
1: The hi hat issue has been resolved.
2: Does the 2BOX receive Program Change messages.
3: Has anyone imported melodic sounds like bass guitar into the 2 Box system.

It seems out of all the hardware modules, the 2 BOX could be a winner. I know there have been some issues with the hi hat so I thought I'd check in and see. Thanks in advance for all input\observations

 on: March 26, 2015, 02:45:19 PM 
Started by mark - Last post by mark

hi guys i downloaded a  version of the soft synth poise. i cannot get it to work with the zendrum. if anyone has suggestion any help appreciated. i am sure it is a simple output or midi channel tweak. i am using it with cubase which works fine with bfd3 and superior drummer. here is a sample video to show what it can do. ok thanks

 on: February 25, 2015, 07:17:52 PM 
Started by rhombus - Last post by rhombus
Okay, I'm using MIDI-OX to test both the hatKAT and a generic volume expression pedal to compare (calibrating again when I switch, of course). The Zendrum receives/sends no signal until the hatKAT is depressed more than half way. With the volume expression pedal, the Zendrum sends/receives a signal throughout the full range of motion of the pedal. I'm afraid the problem (or limitation?) is with the hatKAT itself, which is a shame because I really like its spring action.

Alas, I haven't purchased ZenEdit yet, it's on my list to do for sure. The Nord Drum 2 doesn't have a hi-hat control input, just 6 trigger inputs and MIDI. So I'm trying to use the Zendrum to be the bridge from the hatKAT to the ND2.

I figure at this point we've exhausted the Zendrum end of the cable, thanks much David and DrumWagon for your help.

I wonder if there are any users with specific experience with the hatKAT to tell me if this is just how it works or if it's malfunctioning?

 on: February 25, 2015, 06:28:29 PM 
Started by rhombus - Last post by DrumWagon
I'd hook up the output to your computer and use MIDI-OX, etc to analyze what's being output.  Does the pedal work when connected directly to the Nord? 
You can also export your SysEx into ZenEdit to check what the calibration settings are for the pedal and try tweaking them.

 on: February 25, 2015, 06:19:23 PM 
Started by rhombus - Last post by rhombus
I am certain it's a Z4 circuit board, I've followed the instructions in the manual to get the version number and it's '41'. I've just gone through the calibration again and I'm getting the same behavior. Any other ideas?

 on: February 25, 2015, 05:13:28 PM 
Started by rhombus - Last post by DrumWagon
If it's a 4.x board, you should try to run the calibration function (outlined in the manual) to set the upper and lower bounds of the pedal sweep.

Pages: 1 ... 5 6 [7] 8 9 10